Friday, May 12, 2017

Go Press and Foil Machine revisited

Back in March I wrote a review for the Couture Creations Go Press and Foil Machine. If you missed it you can check it out here.

For the most part, I liked the machine but I had some issues that were bugging me.
Mostly, the inability to get full, even foiling on the large frame stamp die.

Well, I was a bit obsessed with giraffes for a couple months (so was the rest of the world so don't judge me lol) but I went back to this machine this week.

I found a video on YouTube that really opened my eyes. It is from Scrapbooking Made Simple. You should check it out. https://m.youtube.com/watch?v=sVWZ5BBe1i8

For me, since I already knew what this machine was 'supposed' to do, I was looking for some sort of tip on how to get even foiling. She says several times....there is hardly any pressure, you almost think there is no pressure it is so light. That was a light bulb statement for me.

I use my Cuttlebug all the time and I am sure you do too (or your Big Shot or whatever crank type embossing machines are out there) and we all know you need pressure to get a good cut or deep emboss.

We, that is one of the big secrets to this machine.....next to no pressure. You really think surely it needs more pressure. But in reality you should barely feel any resistance.

So, no pressure and longer heating time. Those are my tips for you today!

Here is my first attempt at the frame from a couple months ago.


See how the foil is sparse? That bugged me. Shouldn't a foil machine, when using their dies and their foil and their directions, give you even foiling? I thought so.

Here is my frame from yesterday.


It is Perfect!
What did I do?
I laid the stamping die on the machine, closed the lid and let it heat up for about a minute.
I then laid the foil, background card stock and a shim (a piece of 110 lb white card stock from Staples folded in half) over all of it and closed the lid.
Then I waited. Well actually, I took some pictures of other projects, went and filled my water bottle, talked to Minnie...  I waited probably 5 minutes.
Everything was evenly heated when I ran it through my Cuttlebug.
I rolled it through very, VERY slowly....3 times.
I then removed my foiled cardstock and let it cool completely before removing the foil (this only takes a few seconds)

I was so happy I ran and showed Minnie. She was not impressed....she is a cat after all! lol (Tucker was always impressed but he was much smarter...sorry Minnie lol)


I wanted to be sure this wasn't a fluke so I grabbed the rose die. It's the third stamping die that came with my kit from HSN. I hadn't tried it yet because I didn't want to be disappointed with that one too.


The photo is dark so that the foiling shows up. Look at that! Even coverage! There is a stray bit of foil near the top but that was because I didn't trim my foil small enough...easily corrected.


The pink worked beautifully too!

I used the exact same steps as the frame. I don't think you can really over heat the dies and paper. The machine shuts off after 20 minutes or so if you forget about it. My theory is that if the heat has penetrated all the layers on the machine it works better. Less heat loss moving it to your embossing machine and actually rolling it back and forth.

So I had to retry using cutting dies. Remember, before they were cutting through my card stock as well as foiling. (there is that pressure issue again)


Not any more. I used the same 'sandwich' as on the frame. The cutting dies are thinner than the stamping dies so I really thought there was not enough pressure. I couldn't feel any resistance at all!

But I got perfect foiling with just a slight indentation in the card stock. Yay!

So, what do you do with just an outline of a butterfly?


I pressed mine into some wet Distress Inks. My intention was to then cut it out and ink the edges darker but I like the swirls of ink around the edges so I am going to hold off and think about it for a while. It could make a very nice card front as is....just add a sentiment and there you go. 

And then I thought....it is supposed to foil chipboard pieces. I don't have any (well that's not entirely true....I have some I'm just not sure where lol) but what about foiling die cuts? If I increase the thickness of the shims to mimic the thickness of chipboard...



I could not get a decent picture of either of these but you can see it is blotchy on the 'Father's Day" and you can see the blue card stock showing on the Hello.

I am thinking thicker shims, just a little thicker. Maybe a piece of cereal box....I'll work on it.

But these are not a total loss.



The foil resists inks. I grabbed my Distress Black Soot and rubbed all over the Father's Day. I then rubbed it with a tissue to remove the excess ink. It now looks like distressed metal. The picture doesn't do it justice. It is pretty cool!

And I rubbed Distress Tea Dyed on the Hello. It is very close in color and that one now looks like aged metal. Again, very cool.

The potential with this machine has increased for me. (and I thought it had potential before)

I hope, if you have been struggling with your Go Press and Foil Machine, that this helps you out. 

Once I work out how to get die cuts evenly foiled I will let you know....imagine being able to foil ANY die cut shape (even Cricut shapes) without them having to be cut from toner paper and run through the Minc (which I still love and use)

Happy Crafting and Happy Mother's Day this Sunday!



Oh, and I am still obsessed with giraffes!


Don't tell anybody but this is from one of the BadBaby round robin journals. We aren't supposed to share any pictures until after the swap ends but I couldn't resist (and how can you be a BadBaby if you don't break any rules?)

It was so hard to resist tearing out the pages and keeping this. :-(